\u00a9 2021 wikiHow, Inc. All rights reserved. With the tip attached, put the skins back on the ski, starting from the tip, and attach the tail clip. Carefully peel off the protective backing material and center the skin on your ski. The loop clip should be sitting where the curved area at the end of your ski starts to straighten out, or about 3 to 4 in (7.6 to 10.2 cm) from the end of your ski. To verify center measure to ensure the overlap on each side is the same. Atomic Hybrid Skins for the Backland / Backland W and Backland UL ranges feature Hybrid Glue 2.0 for easy handling and 100% Race Mohair for efficient skinning. Rover tails are adjustable to around 8cm. The remainder of the skis we tested are ostensibly universal in compatibility. wikiHow, Inc. is the copyright holder of this image under U.S. and international copyright laws. Having the back hooks in place before you start fitting the skins will help to ensure that you get the best possible fit. 2. The step below will walk you through how to fit your skins. Research source. 3. While it was a bit frustrating, I found it humorous, and gave me the opportunity to improve technique by rolling my ankles downhill, thus allowing the skin to contact more snow surface. Press down extra hard on any parts of the skin that are lifting along the edges. Touring ski skins or climbing skins are indispensable for all ski runners, ski tourers and free tourers. Put the end of the clip over the bottom tip of the ski and press down firmly. If you would like advice on ski skins or if you can't find what you are looking for please give us a call. 1. skins correctly is to follow the directions on the instructions sheet that is  provided with your purchase. We stock some pre cut skins for popular skis which don't always appear on the site. Always set the length first! There should be slight tension. A little dirt or dog hair won’t ruin our glue, but it is generally advised that you do your best to keep it clean. You need to attach skins with a combination of adhesive and clips that go over the ends of the skis, but the process if easy. Just make sure that there is nothing that will interfere with the skin gripping the back of the ski. Most skins ship with an easy-to-use trimming tool and instructions. Innovative ski skins including Ascension nylon skins, GlideLite mohair skins and accessories. If you feel it’s more than you want to take on, bring them to a backcountry specialty store, or get help from an experienced friend. Your ski buddy’s boot won’t work. wikiHow, Inc. is the copyright holder of this image under U.S. and international copyright laws. In theory, this is a great idea as it allows for a durable skin adhesive that is still easy to remove from the ski. Leave a 4″ to 6″ tab that will double back through the stretcher loop. The “Hybrid” designation describes the glue process of these 100% Mohair skins, which consists of a less-sticky adhesive that holds the ski to the skin, plus a much stickier adhesive that joins the first adhesive to the skin material. wikiHow, Inc. is the copyright holder of this image under U.S. and international copyright laws. [2] References. Pre-heat your wax iron to typical wax-melting temperature and iron the surface of the skin just like you would with your skis. Skinz Plastic Ski Skins Starting from $183.99. If certain manufacturers offer skins that are trimmed to fit their skis, most of the time you will need to trim your skins to your skis. This image may not be used by other entities without the express written consent of wikiHow, Inc.
\n<\/p>

\n<\/p><\/div>"}, {"smallUrl":"https:\/\/www.wikihow.com\/images\/thumb\/1\/1f\/Apply-Climbing-Skins-Step-14-Version-2.jpg\/v4-460px-Apply-Climbing-Skins-Step-14-Version-2.jpg","bigUrl":"\/images\/thumb\/1\/1f\/Apply-Climbing-Skins-Step-14-Version-2.jpg\/aid1401840-v4-728px-Apply-Climbing-Skins-Step-14-Version-2.jpg","smallWidth":460,"smallHeight":345,"bigWidth":728,"bigHeight":546,"licensing":"